Local Reviews
for Naperville, IL
Our Reviews by City
Chris S.
HVAC service. Rewired thermostat and connected customer-supplied thermostat. NC.
Brennon E.
Cleaned and serviced furnace. Replaced furnace filter and hum pad that customer provided. Customer had summer/winter damper closed and was mentioning that humidity in home was low even tho setting was up. Opened damper to fix issue. Tested and cycled system. Found hsi heavily corroded and replaced. Cleaned out exhaust pipe. Tested all mechanical parts. Condensate pump is working accurately. System is operating and heating as it should be at this time. Customer renewed maintenance program and will have cooling visit and next furnace visit prepaid.
Brennon E.
Cleaned, washed out, and serviced condensing unit. Tested capacitor, contactor, fan motor amperage, compressor amperage and continuity. Everything was in accurate working condition. Checked r410a refrigerant levels and those too were in accurate efficiency range. Changed furnace filter that customer provided. System is operating and cooling as it should at this time. Customer will renew maintenance program in fall.
John M.
Commercial washroom drain cleaning. Pulled toilet in back and successfully rodded, pulled back tampons.
Brennon E.
* No AC call. After inspection found faulty contactor and low capacitor. Replaced both parts. Then performed cleaning and wash out of condenser. Unit had not been service in a couple years and was extremely dirty. After cleaning test fan motor amperage and compressor amperage. Both of those were in accurate working condition. Checked R410a refrigerant. That too was in accurate efficiency range. After performing the clean and check and replacing faulty parts, unit is back up and running and cooling properly at this time. * customer wanted to renew maintenance agreement. One visit was used today and they will have one remaining in fall of 2024 for crawlspace furnace. *customer is requesting reminder for fall cleaning a few days before visit.
Brennon E.
Cleaned, washed out, and serviced condensing unit due to maintenance plan. Tested capacitor, contactor, fan motor amperage and compressor amperage. Everything was in accurate working condition. Checked R410 refrigerant levels and they too were in accurate efficiency range.
Dan K.
Commercial faucet repair. Found stem on moen tub valve broke off,I drilled center of stem with 3 different drill bits to get to the right size for a metal Sammie to thread into stem pull out old cartridge and install new cartridge and reassemble valve set warm to a good temperature not really hot due to a kids tub. Material used in notes.
Dan K.
2- electric boilers diagnostic done today 1-North boiler 1 of 3 fuses are blown on main feed going to this boiler, this fuse will have to be changed by a electrician before any other diagnostic can be done on this boiler. 2- south boiler Power is good to this boiler but the low voltage fuse is blown on this boiler this is the control side of the boiler, tried to locate fuse I was unsuccessful on this, I called Dave at the shop he could not locate one at this time we need to order and return for further inspection. Office needs send bill Office had me return today. 12/14/2023 North boiler check no heat 1- boiler has power all three legs pump control is not calling for heat. 2- found floor control turned all the way down this is not a thermostat it control’s temperature of the slab set at 65* boiler is on and heating. South boiler 1- found bad fuse on 24 volt side this fuse was never changed from last time. I replace fuse boiler came on stage one , when the time delay pulled in st
Brennon E.
Cleaned and serviced furnace. Tested flame sensor, pressure switches, hsi, fan motor amperage and capacitor, and inducer motor amperage. Cleaned out exhaust pipe and drains. Washed out furnace filter and reinstalled under blower. Everything is in adequate working condition. Customer has one more visit remaining on plan for condenser in 2024 season.
Brennon E.
Cleaned and serviced furnace. Tested flame sensor, pressure switches, hsi, fan motor amperage and capacitor, and inducer motor amperage. Cleaned out blower motor cabinet. Blew out drain lines. Everything was in adequate working condition. Changed furnace filter that customer provided. Customer has one more visit on plan for spring.
Brennon E.
Cleaned and serviced condensing unit. Tested capacitor, contactor, and fan motor amperage and everything was in accurate working condition. Tested r410a refrigerant levels, and those too were in accurate range. Everything is working greatly. Customer wants to renew maintenance program.
Anthony F.
Leak search with nitro to 450 psi, used bubbles found no leaks held for 30 minutes, pulled vac down to 500 micron added 4.3 #r410a, replaced capacitor 40+5
Anthony F.
AC maintenance. Unit low on refrigerant, customer want to replace air conditioning unit.
Anthony F.
Water leak in the Brown house and clogging the sink lines. Found the water softener to be in bypass mode, programmed timer and hardness into sofetner and put back into service. Ran through regeneration and also performed hardness test on well - 35 grains of hardness. If problems with water persist I recommend chlorinating the well and replacing the water softener
Pete W.
Water heater leaking, needs to be replaced. Replaced water heater
Chris G.
Heating repair. Low heat call out. Customer stated that thermostat said that it had been running for two hours. Upon detailed inspection found the pressure switch to be intermittent. Vacuum started at -1.30 then reduced to -1.00. Pressure switch at -.60. Replaced pressure switch and hose.
Chris G.
Clean and check furnace system. Renewed customer service agreement. This is the first visit on this new plan. 20 cent part from truck inventory
Anthony F.
Clean, test and reset furnace to factory specs for safe, efficient operation.
Chris G.
Clean and check air conditioning system. This is the second visit on this annual HVAC service plan.
Anthony F.
Central air conditioning maintenance. Clean, check ac operation. Reset to factory specs for safe, efficient operation.
Chris G.
Heating furnace repair. No heat call. Customer said air filter was very dirty because of remodeling. Heating system shut down because of high limit. Cleaned and tested furnace and replaced faulty run capacitor. Reset heating system and tested three times.
Chris G.
Heating repair. Found furnace did not have power. Upon inspection found door switch to be intermittent. Shimmed door switch, added note to interior of furnace. Need to replace door switch on next service call. No charge per technician.
Dan K.
Commercial heating repair. Checked temperature around barn floor temperature @50*, before floor was running at 65* check boilers found both boilers missing power on one leg of a 3 phase system, let customer know to call Com Ed to check service transformer.
Dan K.
Commercial furnace repair. Check floor temperature 60* to 68* on most of floor. Found a leak on one zone. Found wire burnt at fuse. Going to replace all the other fuse on this boiler they are soft. Due to age and being in a barn the fuses are paper shell. 2nd boiler is working, fuses are soft due to age, tore apart when pulling them out, replaced all fuses in this boiler.
Anthony F.
Furnace maintenance safety and combustion inspection, recommend lower merv rating filter.
