Local Reviews
for Manhattan, IL
Our Reviews by City
Pete W.
Sump pump service. Tested motor and switch for main and battery backup sump pumps, both tested fine at this time.
John M.
Rubber coupling on pair of pumps became detached because sump line outside froze because it was run above ground. Reattached pump to discharge line, ran 10’ of pvc outside for a temporary fix.
Dan K.
Furnace repair. Tested flame sensor, pressure switches, hsi, fan motor amperage and capacitor, inducer motor amperage, and gas valve voltage. Found furnace locked on flame sensor, cleaned sensor, furnace ignites and is working. Reset to factory specs for safe, efficient operation. Let customer know about our annul VIP maintenance agreement. And he would get 2 check ups a year one on ac unit and one on furnace. He will call in the spring to sign up for plan.
Brennon E.
Cleaned and serviced furnace. Tested flame sensor, pressure switch , inducer motor amperage, fan motor amperage and capacitor, and gas valve voltage. Replaced humidifier pad (35) that customer provided. Furnace filter was just changed by customer. Everything is working as it should at this moment. Customer renewed maintenance program and will have both visits for spring and this coming fall. Gave customer estimates for new furnace/humidifier due to rust build up and furnace from 2004.
Michael M.
FURNISH LABOR AND MATERIAL FOR THE PLUMBING REPAIRS AS LISTED
Chris S.
Replaced customer supplied battery’s.
Pete W.
Water leak. Went up in the attic, found evidence of water staining on 6 inch flue pipe through the roof. Could not see any evidence of plumbing leakage through ceiling in laundry room. believe this is a roof flashing issue.
Brennon E.
No heat call. Started with clean and diagnosing of furnace. Customer wanted to join maintenance member plan. After diagnosing, found high limit switch was failed to the open position. The furnace filter was extremely dirty and clogged up, thus making the high limit fail. Also tested flame sensor, pressure switches, hsi, fan motor amperage and capacitor, and inducer motor amperage. Replaced the high limit switch and hsi due to corrosion. Everything else was in adequate working condition. One visit on plan was used today and customer has one remaining for spring for condensing unit. Performed free inspection.
Brennon E.
Cleaned and diagnosed furnace. Tested flame sensor, pressure switches, hsi, fan motor amperage and capacitor, and inducer motor. Everything is in accurate working condition however furnace in old being from 2005. Has rusty burners and inducer. Gave customer estimates for new furnace and he is considering next year. He did not want to do plan at this time.
Brennon E.
Cleaned and serviced furnace. Tested flame sensor, pressure switches, hsi, fan motor amperage and capacitor, and inducer motor. Everything tested in accurate working. Gave customer estimate for new inducer motor due to slight winding noise that’s it’s producing. Customer has one visit remaining on our VIP service plan for spring.
Brennon E.
Cleaned and serviced furnace. Tested flame sensor, pressure switches,hsi, fan motor amperage and capacitor. Flame sensor and hsi were replaced due to corrosion. Everything else tested in accurate working condition. Cleaned out exhaust pipe and blew out drain line. Customer Renewed maintenance program.
Chris S.
Inspected boiler for season.
Pete W.
Replaced water softener, found leak from pinched seal between head and tank, adapter, contacted Mid-America. They are working on getting the part. Returned to complete install and test.
John M.
Replace tankless water heater never run out of hot water. Test operation and clean up.
John M.
Installing new Tankless water heater
Dan K.
Test and certified 1- 1” RPZ backflow file report with city per state code.
John M.
Installed customer supplied well tank
Chris S.
Service A/C, condensation inside of furnace, blower motor must have stopped working. Everything working at this time. Suggest replacement of system, A/C is 14 years old and furnace is original. Send estimate.
Brennon E.
Condensing unit not keeping up. Tested capacitor,contactor and fan mot amperages. Everything was in accurate acceptable levels. Unit was completely dirty however and very low on refrigerant. Hosed condensing coils out and added 2lbs of R410a refrigerant to achieve accurate efficiency levels.
Michael M.
ESTIMATE TO TEST AND CERTIFY (1) 1 INCH RPZ. LOCK BOX CODE 1970
Pete W.
Found gap in trim for tub valve, checked other possible leak sources, filled gap with silicone and suggested valve replacement.
Chris S.
Toilet leak repair. Pull and reset toilet, new rubber flange.
John M.
Sump pump service. Replaced main sump pump and battery backup with pair of sump pumps.
Pete W.
Sump pump repair. Main sump pump float doesn’t turn off, need to replace pump. Replaced pump.
John M.
Sump pump inspection. Tested sump pump, both primary and backup seem to be working fine. Told customer a new pump is $750.
