Read below what your Frankfort, IL neighbors say about our plumbers and HVAC team. You'll like what you see!
Local Reviews
for Frankfort, IL
Powered by Nearby NowOur Reviews by City
Great Service, Terrible Price
Jim - Frankfort, IL
Pete did a fine job. Less than 15 minutes on site. Invoice does not show individual pricing; just a quantity of 1 for Dispatch fee, tank lever handle replacement, $20 off coupon and a member savings of $45.65. Total cost $184.35. I have dealt with PD&M for over 35 years and recommended them to others on numerous occasions.First time I am totally disappointed. Good thingI am a member. if not the cost would have been $250.00....
Response from PDM Plumbing, Heating, Cooling Since 1885:
Oh boy, sorry for the mix up. Glad Pete got you back to normal. Thanks Jim for sharing and we'll work to keep you happy!
Excellent service at a great price!
Vicky - Frankfort, IL
Anthony, our service technician (plumber) was very professional, friendly and extremely knowledgeable. He took care of the leaky situation quickly and efficiently.
Knowledgeable
Karl - Frankfort, IL
Very professional service !
Mr Steve - Frankfort, IL
Very courteous and professional phone staff with great follow through and my technician, Anthony was very competent, professional and timely in his work on my project. I would definitely recommend them to others.
Nice Job
Farquhar - Frankfort, IL
Pete Was professional courteous and efficient with his work. He did the work neatly safely and courteously. I would recommend PDM to others especially as quickly as they responded and performed the work. I felt pricing was a little higher than I had expected.
Excellent advice and troubleshooting over the phone from your technician on a rainey Sunday night regarding my ejector pump malfunction, followed up b
Steve - Frankfort, IL
Over all
Jim - Frankfort, IL
Day 1, replaced battery on backup sump. Worked find. Day 2, sump died, replaced with new system. 1 hour later alarm for system usage. Day 3, adjusted float level. System back on. Overall, I ask myself was something done (with no malice) that caused the sump to die on day 1. Still think the world of Rudy and will continue to use PDM.
As always, great service
Eighner - Frankfort, IL
Great service
Brian - Frankfort, IL
Technicians always give great tips on maintaining my furnace and AC unit.
Mark M.
Frankfort Butternut Creek Woods plumbing repair. Toilet leaking. Pull toilet and replace wax ring.
Mark M.
Frankfort Butternut Creek Woods water heater service. Install energy efficient tankless water heater.
Mark M.
Butternut Creek Woods neighborhood. Install new whole home air purifier to help with allergies.
Mark M.
Plumbing repair in Ashington Meadows, Frankfort. Replace kitchen faucet.
Dan K.
Replace Sloan stop vacuum breaker and o ring on 2nd stall girls bathroom by boiler room. Note we where out working on contract job this job bill through Dave Moon T and M.
Dan K.
WORK PER ESTIMATE.
Mark M.
Water heater repair Frankfort. Leaking water heater tank. Replace 50 gallon Bradford White hot water heater.
Mark M.
Frankfort plumber certified water backflow device test.
Pete W.
Leaking angle stops under kitchen sink (3)
Chris S.
Need to order faucet, installed new faucet, has bad push button for spray, need to return.
Chris S.
Frankfort furnace repair. Check heating system, Estimated new HVAC furnace and ac system, 8200.00
Dan K.
Furnace repair. Found furnace locked out code 5 which is open rollout switch, reset rollout switch, reset furnace. Furnace lite but flame looked lazy not going into burner tubes like they should. Open front burner panel flames look better. Went outside to look at discharge pipes and found the cone is lose and has ice around bottom . Clean ice off glue cone back on go into house and blow out burners with Co2 . Startup furnace flames are better ! I noticed the termination kit is 2 inch with a reducer to 3 inch at the wall. Being a 125,000 BTU furnace this may be right at the board line for fresh air. May need a 3 inch termination kit. Furnace is working as of this date. Furnace Concord Model CG90UB125D20D-1 Serial S8405J10027 Note when we come we need to bring a 5000 aprilaire filter media also this needs to go in equipment so we know to bring this with us. Bill to be sent later
Dan K.
Work performed on 2/1/2021 this is not a bill but work that was performed. 1/2 inch pen water valve was letting water out. Need to order new valve . AFD 1 was locked out and code 70 was on display. Look at Motor it will not spin, it is locked. I got small pair of channel locks on shaft and freed up. Turn on AFD 1 put on hand pump works . When I flip system over to local and auto system does startup and it runs. I notice every now and then suction pressure drop below 50 psi and the drive shots out a 72 code low suction pressure. When the pressure goes up it clears I am sure, if it stayed down it would lock the drive out. Talked to Rodney and he said to order the pen water valve . Also I flipped the control switch to off, so system will not run. I have pictures of the water valve in photos.
Anthony F.
Clogged floor drains backing up. Rod man drain from clean out in room. Lots of resin in room from softener. Possibly water softener has cracked distributor tube.
Chris G.
Old ejector pump tested bad, not working when plugged directly in. Replaced with a half horsepower ejector pump, with high float switch and new check valve. Old system had no check valve. Caulked lid down and all protrusions.
Chris G.
Water heater repair. Order two sets for the water heater. Two flame sensors two gaskets and two spark rods.to be billed. We need to return and install a new set when the parts come in.
Chris G.
Boiler repair. Replaced 1/2 inch boiler valve with 1/2 inch ball valve and boiler valve. To be billed.
Pete W.
Checked plumbing connections to dishwasher, does not appear to be plumbing related. Suggest contacting appliance repair company
Pete W.
Toilet repair. Replace broken Kohler toilet handle. Test operation.
Dan K.
School water piping repair. Shut down main water and drain system. Remove section of 1 inch copper that was leaking. Install new copper piping. Re-sweat fittings and turn water system back. No leaks. Job is complete. This is not an invoice this is just scope of work that was done on Tuesday, January 5, 2021
Anthony F.
Replace hot and cold angle stops on basement kitchen sink, disconnect ice maker line and add a extension to the cold side of basement kitchen faucet, parts in photo
Anthony F.
Drain cleaning. Rod lavatory drain second floor hall bath, sink closest to door. Tested operation and cleaned up.
Chris G.
Furnace repair. Found three light diagnostic - inducer fan on when I arrived. Board needs to be replaced. Return Monday morning with new board. Replace control board with hot surface igniter and tested. 12/21/20
Chris G.
Furnace repair. Tested inducer system, found motor pulling .5 amps, rated at 1.0 amps. Vacuum pressures low. See notes.
Pete W.
Kitchen sink leak
