Hot Water Heating FAQ

PDM Two Plumbers and Trucks

Water Heater FAQ

With 139 years of water heater experience PDM Plumbing has water heater FAQ answers to your problem.

Safety Tips For A Leaking Water Heater FAQ.

If the leak is major:

1. Shut off fuel supply (gas or electric)

2. Shut off cold water supply to the water heater

3. Open a hot water faucet in your home

4. Learn how to drain a water heater

5. Call PDM Plumbers for quick help.

 

Electric Water Heater No Hot Water.

Gas Water Heater FAQ.

 

Not Enough Hot Water.

Check the thermostat setting, it may be set too low. But be careful, a hotter setting can lead to hot water scalding within seconds. Check the dip tube (sends water to the bottom of the tank), if the dip tube has broken or fallen off, incoming cold water will be drawn out through the hot water outlet without being heated. Other possible causes are clogged burners and low gas pressure. If you have an older heater, scale build-up can be a problem.

 

Pdm Review

Slow Hot Water Recovery. Why Does My Water Heater Not Work As Well As It Used To?  

Usually due to sediment buildup in the bottom of a heater. Flushing the water heater may help. Other possible causes may be insufficient combustion air caused by insufficient ventilation, a clogged flue (could be dangerous and allow carbon monoxide poisoning), or improper burner operation.

 

Pilot Light Is Lit.

Turn on a hot water faucet and let the water run. Check to see if burner comes on. If not, run the hot water several more minutes. If the burner still does not come on the problem could be a defective safety system. Check to see if the control valve knob is in the “on” setting and not set to the “pilot” position.

 

Pilot Light Won’t Stay Lit.

Sometimes a draft will blow the pilot light out. Make sure the burner access covers are in place. Other possible causes are dirt in the gas line, or a gas safety device problem.

 

Pilot Light Is Not Lit.

Follow the instructions posted on your water heater and attempt to re-light pilot with care.

Make sure gas valve is open. If the pilot light will not re-light, the problem could be that gas is not reaching the water heater or a clogged pilot line. Call a licensed plumber for help

If the pilot light will light but does not stay lit when the gas valve control is released the problem could be a defective pilot safety switch or perhaps a loose pilot safety switch connection to the gas control valve. Make sure the pilot safety switch connection to the control valve is tight.

 

Gas Burner Flame Noisy (Whistling).

Problem may be improper gas pressure or dirty burner orifice.

 

Yellow Flame.

Problem could be scale on top of burner, dirty burner orifice, flue way clogged or improper gas pressure.

 

Gas Burner Flame Floats.

Problem may be improper gas pressure, wrong orifice or clogged flue.

 

Discharge From Temperature And Pressure Relief Valve.

The relief valve will open when the water temperature is to high or if the pressure gets too high. If the inlet to the water heater is fed directly from the water main with no pressure relief valves or check valves between them then when the water heater heats the water and it expands, the extra volume of water simply flows back toward the water main. If however there is a blockage such as a check valve or pressure reducing valve with a defective bypass then the increase in water volume has no where to go and the pressure with increase dramatically. Placing an expansion tank in the line at the inlet will give the increased volume of water someplace to go and prevent operation of the relief valve.

Another possibility is that the City water pressure has increased above the setting of the relief valve. Again the installation of an expansion tank will solve the problem.

 

Popping or Banging Noise.

Scale can build up in the bottom of the tank causing all sorts of noises to occur while the water heater is heating water. Try flushing the tank. Make sure you turn off gas or electric before flushing.

 

Sooting.

Combustion air inlets or flue-way is restricted or not enough ventilation air supplied to room. Also, may be improper gas pressure or dirty burner orifice. Remove obstruction or debris from heater or flue way and improve ventilation. An obstruction could create carbon monoxide poisoning.

 

Hot Water Smells Like Rotten Eggs.

Certain types of bacteria can react with the magnesium anode rod resulting in a rotten egg odor. Clean the tank using chlorine bleach or by changing the anode rod to aluminum usually will solve the problem. If older heater, you’re better off replacing with new efficient unit.

 

Rusty or Black Water.

Anode rod may have dissolved or there is excessive sediment build-up. Check anode rod. You may be better off replacing tank with an energy efficient model.

 

Milky Water.

May be as simple as aerated water. Allow a glass of hot water to set for a few minutes. If the water turns clear, the condition is a natural occurrence. If not, call PDM for help.

 

Leaking Water Heater Tank.

Depending on where the leak starts determines if a repair is possible. If from the tank you will need to replace the water heater with energy efficient model. The savings in energy can help pay for the heater. PDM Since 1885 offers same day replacement and a variety or warranties are available.

 

Contact Old Fashioned PDM Plumbers For Water Heater FAQ Help Since 1885. 815-726-6264

Joliet Chamber of Commerce Logo
Herald News Best of Will County 2023 Readers Choice Awards
Schedule Your Appointment Today!
servicedetailscustomerreturningschedule
How Can We Help You?
Your Contact Information
*
*
Have we served you in the past?
Yes
No
What Day Works Best For You?
What time of day is best for you?
First Available
Morning
Afternoon
Back Next